Automatic Flash Point Apparatus 
Test Method : lash Point is Lowest temperature at which application of the ignition source causes the vapour of a specimen of the sample to ignite under the specified condition of the test. The temperature of the approximately 70 ml test specimen is increased rapidly at first and then at a slower constant rate as the flash point is approached. At specified intervals a test flame is passed across the cup, to measure the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions.
Conforms to the specifications of : ASTM D92; IP 36; ISO 2592
Auto Fire Point Detection :
In addition to the automatic detection of flash point , fire point can be determined automatically too.The fire Point is detected when the ionisation ring detects 5 sec for continous burning.
Accessories Will Be Supplied With Equipment :

•  Cooking Bulb — 5 No (Cat No Hamco31s1)
•  Needle — 1 No (Cat No Hamco31s7)
  
•  Syringe — 1 No (Cat No Hamco31s7)
•  Cooking Bulb Filling Rack – 1 No. (Cat No Hamco31ac1)
  
•  Ss Tong — 1 No. (Cat No Hamco31ac2)
• Ceramic Board Plate – 1 No. (Cat No Hamco31s6)
  

Spares Required For 5 Year Trouble Free Operation :

•  Cooking Bulb — 200 Nos.(Cat No Hamco31s1)
•  Temperature Controller — 1 No.(Cat No Hamco31s2)
  
•  Solid State Relay — 3 No.(Cat No Hamco31s3)
•  Switchgear(Mainswitch & Bulb ) – 3 No Each (Cat No Hamco31s4)
  
•  Ceramic Split Bend Heater – 2 No. (Cat No Hamco31s5)
•  Ceramic Board Plate – 1 No.(Cat No Hamco31s6)
•  Sample Filler Needle & Syringe ( Cat No Hamco31s7)
  

Electrical Requirement :

•  220-240V, 50/60Hz, Single Phase, 10.9A
• 5OR 115V, 50/60Hz, Single Phase, 20.8A
  
• Dimension : Ixwxh,in.(cm)
•  16”x21.5”x14.5” (41x55x37)
•  Net Weight: 64 lbs (29kg)

Shipping Information :

•  Shipping Weight: 78 lbs (35kg)
• Dimensions: 8.2 Cu. ft.
  

Automatically Shut The Machine And Horn The Buzzer In The Case :

•  EFP+30oC or at 400oC is reached
•  Temperature sensor is found defective
  
•  Flash detector is found defective
•  Arm is not set in place
  
•  Cup is not set in place
•  Heater has gone
•  Side Ignition coil/solenoid has gone
  

Installation Site :

• Temperature : 0 to 45 degree C. , Humidity : Less Than 90% ( No condensation).
  Utility :
•  Power Supply 230 V Ac, 16 amp.
•  GAS Supply ( LP Gas or Natural Gas Pressure Less than 9.8 Kpa)
  Ordering Information:

CATALOGUE NO	PRODUCT DESCRIPTION	ELECTRICAL REQUIREMENT
HAMCO 19D	AUTOMATIC FLASH POINT APPARATUS	220-240V, 50/60Hz
HAMCO 19D EXP	AUTOMATIC FLASH POINT APPARATUS	115V, 50/60Hz
HAMCO 19S1	CERAMIC HEATER
HAMCO 19S2	THERMAL INSULATOR
HAMCO 19AC1	COC CUP
HAMCO 19S3	SIDE IGNITOR WITH COIL
HAMCO 19S4	COOLING FAN
HAMCO 19AC8	THERMAL PRINTER ROLL